Honda CB750 Sandcast

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - sancastnorway

Pages: 1
1
Everything K0 / Changes on K0
« on: December 29, 2016, 04:14:29 am »
I am starting to restore an 2/70 K0 with frame number CB750-1022139, and I am need to know some detal about some parts.

On what Serial number started the:
- HM300 mark on the exhaust?
- The white foam for the seat?
- The long Chain guard
- Ended the rear rolled rim?
- Ended the recessed ignitin switch
- Ended the wrinckle tank

On front fender, I have seen
- Double cutted With clamp for speedo cable
- Single cutted With clamp for speedo.
- And finally no cut on both ends-

On my CB7501018317, there is a wrinckle tank, double cut fender, recessed ignitin, read foam and rolled rim, unmarked mufflers, short chainguard, so the changes I am looking for is after this number.

I will preciate if someone have some answeer/Serial numbers on this to help me.
Jan

2
Parts Wanted / Sandcast frame wanted
« on: December 25, 2016, 05:28:07 pm »
I need an sandcast frame With frame number between 2800 and 3800, but everything With a title will also doo..

3
Parts Wanted / CR750 Piston
« on: October 30, 2016, 10:49:18 pm »
Maybee not the right place, but I try here also.

I am looking for a set of original 2-ring slipper type piston for my CR750 project. If someone out there have a set for sale, please email me on: jan@tveten.biz

4
General Discussion / Value on a early diecast
« on: June 15, 2015, 04:54:58 pm »
I know that early sandcast is valuable, but how popular would diecast number CB750-1007489 with engine CB750E-1007548 be? As far as I have found out, this also have a sandcast engine, I am not sure yet, but it looks like that. It would be bike number 75 of the diecast series, and I have never seen an earlier frame than this. The bike is bad, but can still be restored.
Jan

5
Engine Electrical / Sleeve and silver/gray tape for restoring wire harnes.
« on: December 23, 2013, 04:46:11 pm »
Long time ago I bought silver coloured electric sleeves and duct tape for some wire harnes on ebay. Now I need more, but can't find somethings on ebay. I need it for my CB750 Police and some other Honda twins
Does anyone know where I can get it?

 Thanks, Jan

6
Motorcycle's Wanted / 1970 CB750 K0 wanted
« on: June 23, 2013, 05:53:00 am »
I am looking for a 1970 CB750 in the serie CB750-102****. I will use it as a donor for a 1970 Police.contact me at mail: jan@tveten.biz
Thanks, Jan

7
Wheels - Hubs - Spokes - Tires / Original tire for a sandcast??
« on: August 15, 2011, 11:11:45 am »
Can anyone tell me what tire a sandcast was deliverd with when it was new? I have a set of bridgestone on it, they look old but I am not sure if they are the original tire....
Jan

8
Exhaust / Muffler, what are correct?
« on: February 19, 2010, 07:41:42 pm »
Hi!
1.
I have bought a sandcast with frame no. 2996 and I am not shure what's the right muffler for it. Now there is a set of very good HM300.
When I look at the part book, I see that there is a change from no.1221 on the upper muffler. Other people say that it is "unmarkd" up to about 3500, then the HM300 comes.
Does anybody know whats rightfor this bike?

2. If I need a set of unmarked, I guess this is hard to find. I see that Yamia have some repros. Does anybody know how good this are?

3. The protector on the muffler, shall this be in dull chrome, or Cd/Zn plated?

Thanks, Jan.

Pages: 1