|
11. Mission Crankcase Cover - Shift
Item |
Change serial number |
Comment |
|
|
|
|
Cover, crankcase mission |
1-7414 |
11360-300-030 |
|
Gasket, crankcase mission |
1 - 7414 |
11395-300-020 |
|
Stopper, shift drum |
1 - 424 |
24430-300-020 |
|
Stopper, shift drum |
425 - 7414 |
24430-300-030 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12. Oil Filter - Oil Pan
Item |
Change serial number |
Comment |
|
|
|
|
Case, oil filter |
1 - 4148 |
15411-300-000
Smooth exterior, no fins |
|
Case, oil filter |
4149 - 7414 |
15411-300-010
External cooling fins added |
|
Case, oil filter |
1 - 7414 |
15411-300-010
Internal strengthening ribs
added to finned oil bowl,
number "2" on outside - Honda
supercession, 26 Jan 1970 |
|
Bolt, oil filter centre |
1 - 7414 |
15420-300-010
14mm head |
|
Bolt, oil filter centre |
1 - 7414 |
15420-300-020
12mm head - Honda
supercession, 26 Jan 1970 |
|
Pan, oil |
1 - 7414 |
11210-300-040 |
|
Gasket, oil pan |
1 - 7414 |
11398-300-030 |
|
|
|
|
13. Oil Pump
Item |
Change serial number |
Comment |
|
|
69/7 Parts manual lists out each individual part w/ corresponding number for the oil pump |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
14. Primary Tensioner
Item |
Change serial number |
Comment |
|
|
|
|
Bearing, ball (6008) |
1 - 5306 |
96100-60080 |
|
Bearing, special ball (6008) |
5307 - 7414 |
91004-300-000 |
|
Ring B, ball bearing set |
5307 - 7414 |
13496-300-000 |
|
|
|
Note: Ring B, ball bearing set not shown in 69/7 parts manual |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
15. Crankshaft
Item |
Change serial number |
Comment |
|
|
|
|
Crankshaft, complete |
1 - 1080 |
10mm threaded hole for rotor fixing bolt |
|
Crankshaft, complete |
1081 - 7414 |
10mm threaded hole for rotor fixing bolt |
|
Bolt, rotor set (10mm) |
1 - 1080 |
|
|
Bolt, rotor set (12mm) |
1081 - 7414 |
|
|
Washer, 10mm |
1 - 1080 |
|
|
Washer, 12mm |
1081 - 7414 |
|
|
Rod, complete, connecting |
1-7414 |
69/7 parts manual calls for one pn for conneciting rod -and- lists four different bearing sizes, identified as A-B-C-D. These different bearings have no pn & are referred to only in measurements of diameter & thickness. |
|
|
|
Parts bulletin 6/25/71, notifies for change to connecting rods by weight codes. The rods have separate codes for weight AND inside diameter; i.e., i.d. size on upper rod half, weight code on cap, having three different size codes - "1-2-3." Differences of weights of these new rods & caps are designated as "A through K." This bulletin denotes Japanese characters for the different rod weight of the earlier rods. |
Back to Table of Contents
|
